Generalaire 1000 SERIES Elite User Manual download pdf

PRECAUTION: The installer should be an experienced service technician. Disconnect electrical power before

beginning installation. Do not install where temperatures fall below 32 degrees F or where plenum temperatures

exceed 150 degrees F. For maximum evaporative capacity, install this humidifier on the warm air supply plenum.

FOR INSTALLATION ON A VERTICAL

SURFACE OF THE WARM AIR PLENUM

OF ANY FORCED AIR FURNACE

INSTALLER: PLEASE FILL OUT AND MAIL WARRANTY CARD AFTER INSTALLATION

IS COMPLETE. LEAVE INSTALLATION INSTRUCTIONS WITH HOME OWNER.

ADDITIONAL MATERIALS THAT MAY BE NECESSARY:

1. 1/4" diameter plastic supply tubing or 1/4" copper supply tubing for hot water applications

2. current sensing relay (G.F. Model #GA50 suggested)

3. junction box, 115 V. grounding outlet, cover and wire

4. 1/2” I.D. drain hose

5. #8 self piercing sheet metal screws

1000 SERIES

FLOW THROUGH

POWER HUMIDIFIER

Select location on vertical surface of warm air plenum of a forced air

handling system for mounting humidifier that allows for service and

maintenance. Do not install humidifier where the blanked off ends of a

cooling coil will restrict air flow to the humidifier.

Cut out a square section

12-1/8” tall by 14-1/8” wide as shown.

Open cover and remove evaporator pad assembly. Humidifier chassis is

self retaining, slide top side in first then slide chassis down. Level chassis

and install eight screws.

COPPER

TUBING

PLASTIC

TUBING

Mount the self tapping saddle valve on either a cold or a hot water pipe.

A side or top mount is best to avoid clogging from pipe sediment.

Connect 1/4” O.D. tubing to the saddle valve. Copper tubing requires a

brass compression nut and brass sleeve. Plastic tubing requires a brass

insert inside the tubing in addition to a plastic ferrule and brass nut.

NOTE: DO NOT USE PLASTIC TUBING ON HOT WATER OR IN

CONTACT WITH ANY HOT PLENUM SURFACE OR DUCT.

INSTALLATION OF THIS SADDLE VALVE MUST MEET OR EXCEED

LOCAL CODES AND ORDINANCES.

Connect 1/4" water supply tube to inlet of solenoid.Connect drain hose

to 1/2" spout on humidifier cabinet using hose clamp if necessary. Run

1/2" hose to suitable drain such as floor drain, sewer or laundry sink. Be

sure hose has continuous slope and is not kinked at any point.

Fresh Indoor Air Quality

FORM NO. 1000-16 REV. E

12-1/8”

14-1/8”

3/4” TEE

1/2” TEE

GCV3412 CODE VALVE INSTALLATION INSTRUCTIONS

Copper Pipe

1. Turn off water supply.

2. Clean pipe, fittings and valve with sandpaper or wire brush.

3. Apply a thin layer of flux to all surfaces to be soldered.

4. Assemble valve to pipe and/or fittings.

5. Cooling the valve by wrapping a wetted rag around the valve is

optional.

6. Heat the joints with a torch. Apply solder to each joint. Continue to

apply heat sufficient to keep solder liquid.

7. After solder has filled entire joint area, remove heat and allow joint

to cool. Do not move or disturb.

8. Slide compression nut over 1/4” copper tube followed by

compression sleeve.

9. Insert tube into valve fully and tighten nut.

10. Turn on water supply and check for leaks.

*CODE VALVE IS INCLUDED WITH AUTOMATIC MODELS ONLY

1 2 3 4 5 6 ... 11 12

Summary of Contents

Page 1 - 1000 SERIES

1PRECAUTION: The installer should be an experienced service technician. Disconnect electrical power before beginning installation. Do not install w

Page 2 - 6A WITH FURNACE CIRCUIT BOARD

Le principe de fonctionnement de l’humidificateur est basé sur la façon la plus efficace et la plus économique d’évaporer l’eau dans l’air. La chaleur

Page 3 - PARTS LIST FOR HUMIDIFIER

42,5 cm (16-3/4 po)43,1 cm (17 po)41,9 cm(16-1/2 po)CARACTÉRISTIQUES DE L’HUMIDIFICATEUR ELITE 1000Le modèle 1000A (GFI nº 5730) inclut :Composants de

Page 4 - HOW THE HUMIDIFIER WORKS

Renseignements sur le produit :Numéro de série : ____________________________________________________________Modèle : _______________________________

Page 5

24V OUTPUT FROM HUMIDIFIER (RED WIRES) OR727-58 24 V. TRANSFORMER WITH CONSTANT POWEROR 24 VAC POWER SUPPLY WITH CONSTANT POWERHUMIDIFIER CONTROL LEA

Page 6 - WARRANTY REGISTRATION

This humidifier, if properly registered by the return of the warranty registration card to the manufacturer, is warranted to the consumer against defe

Page 7 - SÉRIE 1000

1. Turn off water supply and electrical power to humidifier.2. Remove cover, water distributor trough, evaporator pad, pad rails and drain pan. Clean

Page 8 - L’HUMIDIFICATEUR

Model No.Loose (0.75 AC/H)GPDAverage (0.50 AC/H) Tight (0.30 AC/H)Elite 57012800 sq. ft.1200 sq. ft.2000 sq. ft.Elite 900171115 sq. ft.1650 sq. ft.280

Page 9 - GARANTIE LIMITÉE

Product Information:Serial Number: _____________________________________________________________Model: _______________________________________________

Page 10 - ASSISTANCE TECHNIQUE

1PRÉCAUTION : L’installateur doit être un technicien qualifié et expérimenté. Couper l’alimentation électrique avant de commencer l’installation. Ne p

Page 11

77FILS DE COMMANDE DE L’HUMIDIFICATEUR (FILS JAUNES)AC LAC NHUMSNSRINSTRUCTIONS DE CÂBLAGE DE L’HUMIDIFICATEURREMARQUE : TOUT LE CÂBLAGE DOIT RESPECTE

Page 12 - ENREGISTREMENT DE LA GARANTIE

Cet humidificateur, lorsqu’il est enregistré correctement en retournant la carte d’enregistrement de la garantie au fabricant, est garanti au consomma

Comments to this Manuals

No comments

Generalaire 1000 SERIES Elite User Manual

Browse online or download User Manual for Humidifiers Generalaire 1000 SERIES Elite. GeneralAire 1000 SERIES Elite Manuel d'utilisation

Summary of Contents

Comments to this Manuals

Related products and manuals for Humidifiers Generalaire 1000 SERIES Elite